Set up cluster behind a load balancer
When you want to setup a Redis Enterprise cluster in an environment that doesn’t allow DNS, you can use a load balancer (LB) to direct traffic to the cluster nodes.
DNS role for databases
Normally, Redis Enterprise uses DNS to provide dynamic database endpoints.
A DNS name such as
redis-12345.clustername.domain gives clients access to the database resource:
- If multiple proxies are in use, the DNS name resolves to multiple IP addresses so that clients can load balance.
- On failover or topology changes, the DNS name is automatically updated to reflect the live IP addresses.
When DNS cannot be used, clients can still connect to the endpoints with the IP addresses, but the benefits of load balancing and automatically updates IP address are missing.
Network architecture with load balancer
You can compensate for the lack of DNS resolution with load balancers that can expose services and provide service discovery. A load balancer is configured in front of Redis Enterprise cluster, exposing several logical services:
- Control plane services, such as the RS admin console to access cluster administration interface
- Data plane services, such as a database endpoint to connect from client applications
Depending on which Redis Enterprise services you want to access outside the cluster you may need to configure the load balancers separately. One or more Virtual IPs (VIPs) are defined on the load balancer to expose Redis Enterprise services. The architecture is shown in the following diagram with 3 nodes Redis Enterprise cluster with one database (DB1) configured on port 12000:
Setting up an RS cluster with load balancers
- Install the latest version of RS on your clusters
- Configure the cluster with the cluster name (FQDN) even though DNS is not in use. Remember that the same cluster name is used to issue the licence keys. We recommend that you use a “.local” suffix in the FQDN.
Configuring the load balancers
- Make sure that the load balancer is performing TCP health checks on the cluster nodes.
- Expose the services that you require through a Virtual IP, for example:
- Web Management Portal (8443)
- Rest API service (Secured - 9443; Non-secured - 8080)
- Database ports (In the range of 10000-19999)
Other ports are shown in the list of RS network ports.
Sticky, secured connections are needed only for RS admin console service (provided on port 8443).
- Certain LBAs provide specific logic to close idle connections. Either disable this feature or make sure the applications connecting to Redis use reconnection logic.
- Make sure the LB is fast enough to resolve connections between two clusters or applications that are connected to Redis databases through LB.
- Choose the standard LB which is commonly used in your environment so that you have easy access to in-house expertise for troubleshooting issues.
RS cluster configuration
There are certain recommended settings within the cluster that guarantee a flawless connectivity experience for applications and admin users when they access the cluster through a Load Balancer.
- Run the
rladmincommands directly on the cluster.
rladmincommands update the settings on all nodes in the cluster.
The following settings are needed to allow inbound connections to be terminated on the relevant node inside the cluster:
# enable all-node proxy policy by default rladmin tune cluster default_sharded_proxy_policy all-nodes # ensure we redirect where necessary when running behind an LBA rladmin cluster config handle_redirects enabled
An additional setting can be done to allow (on average) closer termination of client connection to where Redis shard is located. This is an optinoal setting.
# enable sparse placement by default rladmin tune cluster default_shards_placement sparse
RS database configuration
Keep LB configuration updated when the cluster configuration changes
When your RS cluster is located behind a load balancer, you must update the LB when the cluster topology and IP addresses change. Some common cases that require you to update the LB are:
- Adding new nodes to the Redis Enterprise cluster
- Removing nodes from the Redis Enterprise cluster
- Maintenance for Redis Enterprise cluster nodes
- IP address changes for Redis Enterprise cluster nodes
After these changes, make sure that the redis connections in your applications can connect to the Redis database, especially if they are directly connected on IP addresses that have changed.
Inter Cluster communication considerations
Redis Enterprise supports several topologies that allow inter cluster replication, these include Active/Passive (https://docs.redislabs.com/latest/rs/administering/designing-production/active-passive/) and Active/Active (https://docs.redislabs.com/latest/rs/administering/designing-production/active-active/) deployment options. When your RS clusters are located behind load balancers, you must allow some network services to be open and defined in the load balancers to allow the replication to work.
For Active Passive communication to work, you will need to expose database port(s) locally in each cluster (as defined above) but also allow these ports through firewalls that may be positioned between the clusters.
For Active Active communication to work, you will need to expose several ports, every database port and several control plane ports as defined in https://docs.redislabs.com/latest/rs/administering/designing-production/networking/port-configurations/. Pay attention to services that are marked with Connection Source as “Active-Active”. These ports should be allowed through firewalls that may be positioned between the clusters.